SARK V6.0.0 Debian install

From sailpbx
Revision as of 18:18, 17 August 2018 by Adminwiki (talk | contribs) (SARK/SAIL Installation)
Jump to: navigation, search

back to SARK contents

SARK V6.0.0 Alpha Debian Install

V6 can be installed onto X86, either wheezy, jessie or stretch (all 64 bit). It can be installed onto ARMEL (32 bit wheezy) or ARMHF (64 bit Jessie or stretch) . It will happily install on a bare-metal Debian, a Debian VM/KVM, or a Debian LXC. It was alpha tested with the following browsers (in alphabetical order);

  • Chrome 68
  • Firefox 60
  • Opera 52
  • Safari 11.1
  • Microsoft Edge 42

It may work on other browsers but they have not been tested so YMMV. It will NOT work on any browser that doesn't support jquery or has it disabled. It will NOT work on any browser that does not support HTML5 or CSS3.

Before you begin

Upgrading from a previous release
  • N.B!! - IMPORTANT! - V6 uses HTTPS so, before you begin an upgrade you must ensure your SARK 4.x firewall has a rule for HTTPS (TCP 443). Otherwise you will lock yourself out and you will need to manually add a rule using SSH or a glass screen attached to the server.
  • If you are upgrading from V4.0 or V3.x, the SARK browser application will force you to change your password. This will change BOTH the browser AND root passwords.
  • If you are upgrading from 4.1 and you are still using the default browser password, the SARK browser application will force you to change your password. This will change BOTH the browser AND root passwords.
New install
  • V6 is designed to run as an appliance, it must not be installed onto a multi-purpose system that has other software already installed on it. If you try you will likely break both the existing systems and SARK. You must begin with a Debian minimal install which contains nothing but an SSH server.
  • The first time you log in, the SARK browser application will force you to change your password. This will change BOTH the browser AND root passwords.

SARK/SAIL Installation

Proceed as follows;

Login to the linux console on your box and Install the GPG key for the 6.0 repo

wget  http://sailpbx.com/sail/sail-6.0/debs/sail.gpg.key
apt-key add sail.gpg.key
apt-get update

Now run ONE of the following depending upon whether you have wheezy or jessie installed

EITHER (wheezy)

echo deb http://sailpbx.com/sail/sail-6.0/debs/repo/ wheezy main >> /etc/apt/sources.list
apt-get update

OR (jessie)

echo deb http://sailpbx.com/sail/sail-6.0/debs/repo/ jessie main >> /etc/apt/sources.list
apt-get update

OR stretch)

echo deb http://sailpbx.com/sail/sail-6.0/debs/repo/ stretch main >> /etc/apt/sources.list
apt-get update

Installing a Mail agent

If this is a new install, you should install a mail agent. SARK has on-board support for a lightweight mail agent called ssmtp. If you install it then SARK will provide a tab in the networking section for you to configure it. Install it now (so that SARK can set the correct perms) with...

apt-get install ssmtp

There is a setup guide for Asterisk vmail to email HERE

Installing/upgrading the SARK/SAIL deb

apt-get install sail

The install will take a good few minutes depending upon the speed of the donor box and your internet link. During the install you will be asked to enter root passwords for both MySQL and LDAP (make a note of them, you'll need them later). You may also be asked to enter the international dial code (IDD) for your country. For example, if you are in the UK, this would be 44. It will also ask about dumpcap but just take the default (No).

Let the install run to its conclusion.

upgrading the SARK HPE deb

If you are upgrading from an older release then should also upgrade the HPE

apt-get install sailhpe

Seed the CDR database

If this is a new install then now is a good time to seed the Asterisk MySQL CDR database with the following command. When it asks, enter the password you gave for MySQL admin during the SARK/Sail install.

mysql -u root --password < /opt/sark/stat/asterisk-stat-v2/cdr-mysql-setup.sql

Install Asterisk extra sounds package

If this is a new install then SARK requires the Asterisk extra sounds package.
If you want UK English, there is a deb on the repo

apt-get install ast-en-gb-gpl-gsm-sounds

If you want "Alison" (US American), there is no deb available for this but it's pretty easy to install. At the linux CLI do the following

cd /usr/share/asterisk/sounds
wget http://downloads.asterisk.org/pub/telephony/sounds/asterisk-extra-sounds-en-gsm-current.tar.gz
tar xvfz asterisk-extra-sounds-en-gsm-current.tar.gz
rm asterisk-extra-sounds-en-gsm-current.tar.gz

Upgrade wheezy systems to Asterisk 11

V6 can run with Asterisk 11 or Asterisk 13 . If you are running wheezy then you should upgrade from Asterisk 1.8 to Asterisk 11 - proceed as follows

echo deb http://http.debian.net/debian wheezy-backports main >> /etc/apt/sources.list
apt-get update
apt-get install -t wheezy-backports asterisk

The Asterisk installer will repeatedly ask you if you want to overwrite existing copies of the asterisk config files. Just take the defaults (press return)

Clean up

You're done - reboot it

reboot

your sail app will be at https://your.server.ip.address but you can just type the bare address (e.g. 172.16.5.123) and Apache will figure it out.

  • UID - admin
  • PWD - sarkadmin

Close your browser and re-open it if you were previously running an earlier version of SARK. If you don't, you'll get odd looking output as the cached jquery code fights with the new V5 output.

Unless you are upgrading from 4.1, AND you have changed the default browser password, then the first time you login, the SARK browser application will force you to change your password. This will change BOTH the browser AND root passwords.

OK, you're done; unless of course you'd like to run the ldap directory feature, in which case read on...

LDAP install

Assuming LDAP is already installed on your SARK/SAIL box (it will have been installed by the SARK install), proceed as follows;

Check the LDAP Base Name (Base DN)

You can check by running slapcat as follows:-

root@deb8ct-test2:~# slapcat
dn: dc=nodomain
objectClass: top
objectClass: dcObject
objectClass: organization
o: nodomain
dc: nodomain

The base name appears in the first line of output. In the above example it is "dc=nodomain". We've used "nodomain" as an example because you'll likely see it a lot, particularly when you are spinning up LXC instances and the like. It just means that LDAP couldn't find the FQDN, probably because it wasn't set. It's no big deal, you can just go ahead and use dc=nodomain if you like. In any event, you should enter whatever YOUR base name is into the Globals=>LDAP panel along with the LDAP password you chose during the install.

If "dc=nodomain" bothers you then you'll need to enter a domain name in SARK, issue a commit and then do a reconfigure for slapd (the LDAP daemon).

dpkg-reconfigure slapd

This will allow it to have another look.

Adding the contacts OU

Now we need to add an organizationalUnit(ou) for the address book. If you are already a whiz with ldap then just go ahead and do it, using the base name. If you don't know ldap then proceed as follows...

You will find a file on your SARK box at /opt/sark/cache/ldapcontactou.ldif

dn: ou=contacts,dc=sark,dc=aelintra,dc=com
objectClass: organizationalUnit
objectClass: top
ou: contacts

Without getting into the details (you can read about ldap elsewhere); in the first line of the file is the name of the organizationalUnit we want to create. In our example it is "contacts". The remainder of the line (dc=sark,dc=aelintra,dc=com) is the base name we discussed earlier. You must edit the file to make the file match your base name from the slapcat you did a couple of steps back. If, for example, you have a base name of dc=splodge,dc=soap,dc=com then you should make your file look like this

dn: ou=contacts,dc=splodge,dc=soap,dc=com
objectClass: organizationalUnit
objectClass: top
ou: contacts

Ok, lets add it, we are going to use the LDAP slapadd utility, which is old fashioned nowadays, but easy to use.

service slapd stop
slapadd -l /opt/sark/cache/ldapcontactou.ldif
service slapd start


Refresh your browser and navigate to SARK. You should see a "Directory" option when you click on the "Settings" drop-down. In this page you can add and modify your telephone book entries or upload a vcard file you have exported from Google contacts or whatever. You can also have your phones browse your contacts if you have SIP phones which are LDAP aware (many are). You'll need to add a couple of entries to your SARK firewall for TCP ports 389 and 686 (restrict them to net:$LAN) to allow the phones to query the database - don't forget to restart the firewall.

Set up your phones to use LDAP

Most major SIP Phone types can use LDAP however, the implementation varies from type to type.

Snom, Panasonic (KX-HDV) and Yealink all support LDAP and have on-board provisioning already set-up for openLDAP on SARK V5.

Cisco small business phones (SPA) support LDAP and Provu have a section on their website showing how to set them up http://blog.provu.co.uk/item/234

Polycom phone set-up is more complex (isn't it always?), however there is good documentation provided by Polycom so you should be able to get it running with a little work although we don't show it here.

Aastra's do not natively support LDAP. However, it is possible to program it in using their XML capabilities and a php server stub. There is documentation elsewhere on the web detailing how to do it.

Gigaset professional (N series) phones support LDAP and there is documentation on their website

Post Install Fixes

  • Some old fixes may be needed as they have not been incorporated here as yet.
  • Set the mode=new in line 6 of /etc/asterisk/say.conf
  • If you are installing SAIL on any OpenVZ (or other virtual) container, when the Stop PBX button in Settings -> Global page, the icon does not become a play button. A second press is needed. To mitigate this, insert a sleep(1); line in /opt/sark/php/sarkglobal/view.php as in the lines below:
private function sark_stop () {
	
if ( $this->distro['debian'] ) {
	`/usr/bin/sudo /etc/init.d/asterisk stop`;
}
else {
	$ret = ($this->helper->request_syscmd ('/usr/bin/sv d sark')); 
   	$ret = ($this->helper->request_syscmd ('/usr/bin/sv k sark')); 
}
	sleep(1);
	return ("Stop signal sent");
}

Known bugs/issues in V6 as at 8/2018